Search results

Hi n2aws, which of the two flow diagrams would you recommend. with the function nodes or without? I want to make sure of everything before I go live.

You have the times set correctly for that. I can't see if you have the 1 and 0 set to send at those times, they are further down the list. I have ON MSG and OFF MSG both set to 1, Should OFF MSG be set to 0? Read the battery voltage, if below X, send the bulk charge command...

The charge timer is set to turn on at dusk, and off at 2am, I thought? My original end goal is to initiate a Bulk Charge at dusk if my voltage is at or lower than the Recharge Voltage settings. Or in-between the Recharge Voltage and the Float Voltage. Thats why I originally injected a range...

Does this look any better?

n2aws Could you chime in on my post 24 & 25. Am I at least on the right path?

So, would I put this charge window, in a range node? And could I let's say use my recharge voltage for the low side, and float voltage for the high side. Would this node be placed before the bigtime node or after?

OK, I found this Modbus map, #503-0246-01-01_R. I believe this is the correct one. So is this where I enter a HEX values. and what about specifying what type of charge Bulk=1, ...

Ok what the heck is HEX 165,

n2aws, do you think I should set up my recharge voltage on a timer, e.g. to go on every evening for a set time. Or can it be programed through Voltage Recharge to enter a bulk charge when needed. But then would I also have to also program it to turn off Grid Peak Load shave so it can do a bulk...

Alright Ya kind talked me into this guy. I really need this inverter to be hands free. I've been checking out Node Red, have it installed on my lapper. About to order a 4G Raspberry Pi from Amazon. Wish me luck. I predict lots of questions. So, what I'm thinking is having the grid peak load...

I will look into this; I've seen Raspberry PI on Amazon. But it still seems way above my skill set. And I was just to really starting to like this inverter again. What a disappoint. Thanks

Thanks guys, I thought for sure this was a simple adjustment. If there was a way to make this work, one of you guys would have found out how. Thanks Regarding Node Red, I don't even know what that is. Is it some kind of pro logic controller. Its above my comfort zone of knowledge.

What if I were to set the Peak Load Shave timers to turn off in the evening. With the Load Shave off would a Bulk recharge occur then? I know this is a band aid not a fix, but I do not want to baby sit this system. Living in the midwest we have long stretches of cloudy days.

I am trying to fine tune my system to make it as hands off as possible. I am running into a problem with the Recharge Voltage setting. I was assuming that the inverter would enter into a charge cycle when the voltage fell below the set number. I had mine set at 51volts, and nothing happened when...

how's this.

Not sure how to make it more readable.

Wow I had just changed them again to do some fine tuning. I have her dialed in now. (I hope) ha ha I hope this helps you.

I am running my xwpro 6848 open loop, with romangeek,s settings and it works great.

Thank You romangeek I have been struggling with this for a long time now. My system is now performing as it should,

Thanks

Where can I find this V1.11 bn28 firmware, Is it still available?

Grid Support Voltage is at 64v

I just downgraded my Insight Local firmware to v1.17. As you can see, it didn't work.

Once I have my batteries charged, I want the solar input to sell to the grid. Yes, I have a CLP, and my SOC is not set up yet. So, its disabled.

AS soon as my batteries reach full charge, they begin to discharge into the grid.

What would you recommend for rapid fire shutdown using a sma 5000tl.

I have a fault 82 on my conext mppt 100 600, How do I clear this?

working as it should, Thank You to Everyone for all your great advice.

got it, Thanks