This was my solution to fitting 4AWG THHN/THWN-2 in those smallish terminals.
Freshly stripped 4awg
10awg crimp die and hydraulic crimping tool.
Fits very well.
I've installed quite a few heated slabs/sidewalks over the years. If you don't fully insulate below your heat source, your system will not be very efficient...
You may also want to consider a glycol based antifreeze instead of the water.
I just received some new panels last week. 415Watt Mono PERK 1/2 cut with STC VOC of 38.82
The next morning I opened a pair to test the voltage. Cool temps 38F and clear skies. At 11:00 am and a 30 degree angle the VOC was 36.2.
Three hours later a front had moved in and I retested. Overcast and...
I have roughly the same system (few more panels and the server rack batteries)
1- The inverter is not bonded. E-mail verification from sun gold power and a visual by me.
2- I use a 600V / 32amp pv isolator.
3- I use a victron on/off battery switch, 275amp/48V nominal, You will also want a 200amp...
I purchased a L14/30R (female/receptacle) and a L14/30P (Male/Plug) ends last week at Lowes to wire in my chargeverter to the battery room.
Both were under $25.00. Saw similar at HD this week for roughly the same price.
I have installed 3 different roof arrays on metal trapezoidal roofs using these z brackets.
Brackets bolt to panels, foot is attached to the flat of the roof with exposed fasteners directly into the purlins. The foot has a pre-installed butyl seal.
Its the most secure and cheapest way I have...
I'm off grid as well and have discarded quite a few on demand pumps over the years. None lived up to my expectations.
Been running this https://www.harborfreight.com/1-hp-stainless-steel-shallow-well-pump-and-tank-with-pressure-control-switch-950-gph-63407.html for 3 years with zero issues. You...
I went with no rails. Trapezoidal metal roof, S5 VersaBracket-67 mounted on the flat, directly into the purlins, in portrait.
Roof metal profile and panel width will determine panel spacing. Purlin spacing on center will determine where the brackets mount on the panels.
EZ-PZ after doing the...
Installed this last year, I know how many attachment points you have.
Shouldn't be too difficult to use some "L" angle and/or uni-strut to bolt directly to the (thousands of) bolts connecting the arches. As stated Landscape will probably work best. If you don't have panels yet, you could...
Brand New, approx 50% SOC.
Manual - Recommended charge Voltage - 54.5V
Manual - Standard Charge Current - 50A
Is this the preferred settings or are there "Better" Recommendations? I'm in no hurry, batteries will not be installed for several weeks.
Thank you, that is the answer I was looking for. Yes, only PV frames grounded. Now to determine how to disable the N-G bond in the inverter. The user manual isn't clear or I cannot find it. Anyone who has disabled it in the SP6548 please let me know,
Just a follow-up.
Reply from SunGoldPower.
https://signaturesolar.com/blog/demystifying-neutral-ground-bonding-in-solar-power-systems-with-eg4-inverters/Also found this at Signature Solar.
I know there are many discussions on the topic but I am still confused.
This will be a 1st time install (DIY) in a totally off grid cabin. The system will be a SunGold Power 6548 inverter, 8x 415watt panels and 2x 48v 100ah server rack batteries.
Is this crude diagram of the grounding of the...
So, are you saying I can charge the batteries with the chargeverter via generator and supply a load from the batteries at the same time? That would really simplify thing if possible.
Off-grid planning stage.
Would like to supply ac in power to a 120v single phase inverter from a generator 240V L14-30R outlet by using 1 leg of the outlet to the inverter for small loads, and the other leg to also supply 120V via a TT-30R to a chargeverter fitted with a TT-30P. Any issues to be...