Hi.
I got the epever up-hi 3000 hm10022 hybrid inverter. It has a dry contact relay , that i can set "close" on a voltage, and then ",open" at a voltage.. its for starting a generator.
Its many autostart diy kit out there, but i can't see whitch of them that is conrrolled with this type of...
Hi.
Android phone..
Any of you seen this before? Why has some of the words not enogh room? Like "remainin g" and i can't see the digits on "voltage diff" ..
Is there a setting on the phone that can make room for everything on-screen? Besides that it works fine.. its the app from overkill..
Hi.
I got me a batterypack ,- 24v 6.3kw li-ion. 3p 7s . They are 3.7vx90A/cell i think.
The seller could not say what model or type the cell is.. but its from a ev/hybrid car.
he just had the charger parameters; bulk- 28.7 v (4.1v/cell) . I planning to rebuild the battery box, and replace the...
hi.
i have a epever up-hi 3000 hm10022 hybrid inverter/charger.
Li-ion 3.7v/cell 7s 24v/270A battery
1000w solar
recomended settings from dealer:
Boost 28,7v
Absorbtion 120min
float 28.5v
Boost reconnect 28v
today, its sunny all day, charging in boost from 27.5v .. . all good..
then...
My Xiaoxiang App for the overkill smart bms crashing when the current goes negative.. tried to do a battery test, and disconnected the panels, connected a load , then the Xiaoxiang App shut down. Strange.. when i try to reconnect, it start in a second, then shut down. If i stop the discharge...
Hello.
I have two jk B2A8S bms mounted on two 250a 24v li ion batteries. All working fine. No alarms.
I find that one of the batteries selfdischarges faster over time(several weeks) than the other one. The battery Main switch is turned off at this time.
Can one of the bms be foulty?
I would...
Hi.
I have a cabin with a 24v 12kw li-ion battery setup. 230v/3000w inverter.
Its installed a heating cable in the insulated batterybox that is controlled by a 230v temp thermostat. In wintertime, when i arrive at the cabin , i turn on the inverter, the heating cables heats the batteries to...
Hello all you creative inventors out there..
I have this remote cabin with 800w solar and a 24v/230v/3000w inverter. kind of a modern setup in a small cabin far into the woods.. in february to september its no problem, plenty of Solar/battery power. But in the darkest wintermonths there is...
Hi.
I have the Victron SmartShunt monitoring my batteries. All of my stuff is mounted inside a metal cabinet. That's so the mice don't get in.. it's in a cabin in the woods..
But,- then , I get a very poor bt signal from the smartshunt! The whole idea was that i could read the monitor from...
Hi.
I finaly got my solar upgrade done.
24v 270a li-ion ev battery, epever hybrid 3000w inverter/charger.
All working fine, good ballance in all cells. Qucc 200a smart bms, victron smartshunt.
But i'd like to get it as good as possible can, so i want to do a capacity test to get all the...
Hi.
Anyone tested power draw from a victron gx lte 4g transmitter/receiver vs using a 4g wifi router to connect from a cellphone ore remote pc?
I need a new router, but do the victron gx lte use less power?
Tryin to make it use as little power as possible in the darkest winter days when...
I have a epever up-hi 3000 hm 10022 hybrid inverter. It works just fine, doing its thing.. but some settings I just dont get right..
"Stop the mains chargings voltage" and " restore the mains charging voltage" settings. I asked the support, thay just said its for start and stop of the...
Hi.
I have this all-in-one inverter/charger in my solar system. Works great.
Ifs a Epever 3000-hm10022. 3000watt/230v max 100A charge 24v battery.
But now, when i connect the generator, a loncin(predator) 3500i , to the grid (generator) input , the generator goes into overload mode. I'v...
Hi.
I'm planning swapping my qucc smart bms to a jk smart heat bms.
About the heat output; do the bms start heating ALWAYS if the temp sensor open for heating? Or do the bms ONLY start heating when charging and the temp sensor open for heating? Or is all this adjustable in the settings?
Any of you tried to adjust the temperature probe on the qucc bms? Mine (1) is 8°c off. Used a glas with icewater, dropped in a digital temp probe to check.. its 4°c. Put the temp probe from the bms in,- it shows 12°c.
I use the xiaoxiang app.
Hi.
I got this offgrid cabin, 800w pv, 220v/3kw hybrid mppt inverter/cc , generator, 24v/6.3kw nmc battery pack from a KIA Soul.., qucc 200a smart bms. Bms low/high set to 3v/4.2v
Cell min/max is 2.5/4.3v .
Ihave set the bulk at 28.7v/4.1v and float at 28.5v/4.07v . Bulk reconnect at...