Recent content by glamsland

Thanks for answer. The wheel are 1.5m in diameter, so its got alot of power with all that water pulling. And i was thinking about this gear unit from Aliexpress, the waterwheel dont go fast, but its powerful, so the gear ratio fits fine.

Hello all you creative inventors out there.. I have this remote cabin with 800w solar and a 24v/230v/3000w inverter. kind of a modern setup in a small cabin far into the woods.. in february to september its no problem, plenty of Solar/battery power. But in the darkest wintermonths there is...

Yes, the best would be to have a standalone panel just for the heater. Then it wont mess with the batteries.. maybe the panel will be covered in snow, maybe not. With luck, the temperature in the battery is on the +side when i get there in the winter. Is'nt it like using a 100w heater on a...

Hi. I have a cabin with a 24v 12kw li-ion battery setup. 230v/3000w inverter. Its installed a heating cable in the insulated batterybox that is controlled by a 230v temp thermostat. In wintertime, when i arrive at the cabin , i turn on the inverter, the heating cables heats the batteries to...

Thanks for answers, I'l do some testing and report back my findings.. I will also check the balance setting. The batteries are of the same type cells, all cells are tested with a capacity tester. After a storrage period on my cabin, with main switch off, its allways battery 2 that is slighty...

Hello. I have two jk B2A8S bms mounted on two 250a 24v li ion batteries. All working fine. No alarms. I find that one of the batteries selfdischarges faster over time(several weeks) than the other one. The battery Main switch is turned off at this time. Can one of the bms be foulty? I would...

I ask this question becouse i'm looking for any ways to try to save some power. Here in norway its getting dark now in november, and at my off grid cabin its wery low chargig ang to high resting power consuption from the inverter/charger (epever up 3000hm10022) its about 30watt/h just having...

Anyone tryed this "Smart Sleep On" setting? What do this setting do? Is this the same as turning off the bms with long-press on the button?

Now this came out on youtube... Something new going on?

There is a new wifi module in the marked now. I asked the support about it, it is in stock, but it's taken back for an upgrade.. so soon the new version are ready.. its wifi, - redy for cloud. The name i wifi module rf45 D https://www.epever.com/product/epever-wifi-adapter-2-4g-rj45-d/

Agree to that the heating should heat before the temp cutoff turns on. Only thing could be that id the battery is stored in the dark wintermonths with litle solarpower, it will drain the battery(maybe.. ) , so in my case,- i have the battery in a remote cabin, with not so much solar power in...

Hi. I'm planning swapping my qucc smart bms to a jk smart heat bms. About the heat output; do the bms start heating ALWAYS if the temp sensor open for heating? Or do the bms ONLY start heating when charging and the temp sensor open for heating? Or is all this adjustable in the settings?

Thanks. Interresting... seems the victron is the one that uses the least amount of power.. I think average wifi router is about 5watts.. but have not tested myself. Guess i need to order a victron then.. ?

Hi. Anyone tested power draw from a victron gx lte 4g transmitter/receiver vs using a 4g wifi router to connect from a cellphone ore remote pc? I need a new router, but do the victron gx lte use less power? Tryin to make it use as little power as possible in the darkest winter days when...

I stil have'nt found a way to display the battery temp sensor on the main page in the App. It can be seen in the setting, but not on the main. Its the same issue on the external lcd monitor for the bms. I kinda just have to trust the bms doing its job..