-
-
EG4_Eric replied to the thread Do i ground the solar panel frame to my house main panel or the load center? My 6000xp is back up by the AC coming from the house..I would recommend grounding the panels to the earth ground of the home. -
EG4_Eric replied to the thread Why am I getting long time drops.It appears that around 4:00 PM yesterday, the voltage from your MPPT #2 dropped and hasn't recovered. I suggest inspecting the...
-
EG4_Eric replied to the thread How to connect 4 powerpro batteries to 1 18kpv.Here is a diagram of how you would connect the communication cable to the 4th battery.
-
-
EG4_Eric replied to the thread How to connect 4 powerpro batteries to 1 18kpv.I would recommend Drawing #2. This should allow you do add the 5th battery as well.
-
EG4_Eric replied to the thread eg4 6000 xp.Here is a link of the distributors list. Feel free to reach out if you have any questions.. https://eg4electronics.com/distributors/
-
EG4_Eric replied to the thread Chargeverter plug adapter.Thank you for the heads up! I'll make sure to report this and get it fixed.
-
You might want to correct the diagram. For 208v, it says (phase). Which isn't correct. It takes 2 Lines for a phase. L1 and L2 are...
-
EG4_Eric replied to the thread Chargeverter plug adapter.If you do decide to rewire the plug, here is how you would rewire it. Also, I'll attach the link to the manual in case you want to...
-
-
EG4_Eric replied to the thread EG4 6000XP overload.If you would like to dm me your serial number I can review the data and see if I can detect what caused this issue.
-
EG4_Eric replied to the thread 18kpv panel configuration.I would recommend to do 8 panels in series to input 1 and 2 for MPPT 1. Which would be 300.8V and 17.7A. This would be recommended over...
-
EG4_Eric replied to the thread Two 6000xp in Parallel Consumption Energy.No, the maximum charge current for each inverter is 125A. Therefore, you could do a total of 375A with three inverters, but it is not...
-
-
EG4_Eric replied to the thread Please suggest a hybrid inverter that works on PV and grid together.You could get this done with the EG4 18kpv. You would have to adjust some settings but it would definitely work...
-
EG4_Eric reacted to Deemib's post in the thread Two 6000xp in Parallel Consumption Energy with
Like.
Thank you much for the prompt reply 🙏 -
EG4_Eric replied to the thread EG4 6000xp MPPT.Yes, you would be wasting a lot. You would only use 4kW and the rest would be wasted. So if you paralleled 2 strings of 3,700W you would...
-
EG4_Eric replied to the thread Two 6000xp in Parallel Consumption Energy.I would make sure that the "Maximum Discharge Current" or setting 9 is set to the combined 420A. For example on the image below it is...
-
-
EG4_Eric replied to the thread EG4 PowerPro Firmware.Yes, I'm certain.
-
EG4_Eric replied to the thread 6000XP - PV1 and PV2.You would need a minimum of 120V per MPPT. I would also make sure the PV input mode is set to "4:Two MPPT connects to different strings"
-
EG4_Eric replied to the thread Maximum PV current input.As mentioned by Sunshine_eggo it is recommended to follow the Specs on the manual of the inverter for safety reasons and also for best...
-
Thanks @EG4_Eric
-
EG4_Eric replied to the thread EG4 Hybrid Solar Minisplit Beep Disablement and Indoor Unit Fan Speed Request.unfortunately, the beeping sound cannot be turned off as of now. However, I will send these request to our team.
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
