@ Johnny
It is best to remove your App and install it again and restart then.
I have posted the download links of Epever below
eBox-BLE-01 op Android inrichtingen voor de afgedichte batterij.
eBox-BLE-01 op Android inrichtingen voor de lithiumbatterij
Ik heb een slechte PWM-controller namelijk (MPPT T40 40A Solar Laadregelaar 12 V 24 V) geeft zicht op een MTTP wat het totaal niet is en kan de batterijen beschadigen en brand veroorzaken !
Ik krijg namelijk pieken van 16 Volt en meer terwijl Float Volatage is ingesteld op 13,8Volt!
Deze ga ik...
iks gewoon een aanhangwagen voor de Goldwing om kampeermateriaal in te vervoeren, het zonnepaneel heb ik zo gebouwd dat het kan opklappen voor mijn frigobox te plaatsen tijdens vervoer
I have the BM819
https://nl.aliexpress.com/item/32869189864.html?spm=2114.13010708.0.0.3a994c4daQCPjB
BM819 true value digital clamp meter
1. automatic range measurement
DCV:400m/4/40/400/600V,
ACV:4/40/400/600V
ACA:4/40/400/600A,
Resistance: 400 /4k/40k/400k/4M/40M Omega.
Capacitance...
It may seem like a stupid question?
But I want to hang my meter on the exit of my solar panels, so these are in series under 24 volts.
But if you look at the diagram of the meter, it should be powered by the battery that is parallel, so below 12 volts.
So I suspect that this can cause a...
Ik ben een ongeldige persoon en heb al mijn kennis uit je YouTube-video's gehaald en ik heb er ook mijn systeem uit gebouwd. Bedankt voor het delen van de kennis
What I have now I show in the print screen below. I had no problems with that because it is about the same voltage
1 = controller output to battery = 12 Volts
2 = output to my fuse box = 12 volts
3 = output of my 220 Volt inverter
So I want one more to check my solar panels but these are in...
The information I have is not really correct?
a) I get the message that it is 24 volts while at the same time my batteries are connected in parallel as solar panels under 12 volts?
b) I get the message that my device is a TriRon 4210 while it is a Tracer AN 4210?
I have already disconnected...
My schedule is like Will's Blueprint. Panels in series and batteries in parallel
And what I want is to connect this capacity meter coreckt
So I want to measure the data of my panels
That is correct idd that I can read everything via the MT 50 but I would like to have had an additional meter of my panels
So if I want this how would I connect them measure like my first screenshot or my second?
Idd when the sun is gone, the meter will be without power and fall out but as soon as the sun is there it will work. that's no problem.
So if I'm good for it, I can connect my meter like the screenshot below
Dear Johnny
I see on you print screen: If you now press (READ) in these settings, you will also see the set time of your background lighting of your controller.
And to set the time between your GSM and controller with timer First press (Read Time) followed by (Synchronize time).
.
See...
ok I'm going to try to be clearer so that you understand me better
This Movie
If you look at a post from me below you see a film from an installation at the end you can see that this maker also measures everything separately, with similar capacity meters and also its batteries are 12 volts and...
Thanks to everyone because I finally succeeded with your good advice, the capacity meter external power connected directly to the battery and now the meter no longer fails thanks to you everyone.
I can now read everything from my proceeds.
a) incoming panels.
b) 220 Volt outgoing via...
I had a bad PWM controller that went into overvoltage the seller wanted me to destroy him and send pictures of it and then buy a more expensive one from him, I turned on the help of AlExpress a few days later completely refunded my money